analog on soldernerd

RX/TX Sequencer

Thu, 11 May 2017 00:00:00 +0000

Much like the beacon keyer presented here earlier, this RX/TX sequencer is a simple but useful little device. Its typical use is in ham radio applications when a separate power amplifier (PA) and/or a sensitive low-noise pre-amplifier (LNA) is used. Care has then to be take to safely transition between RX and TX states - and that’s where this sequencer comes in.

Ultrasonic Anemometer Part 19: Testing the Analog Circuit

Tue, 26 Apr 2016 00:00:00 +0000

In my last post I went through the design of the analog part of the ultrasonic anemometer. Today we will see how the circuit designed last time performs in practice.

Ultrasonic Anemometer Part 18: Analog Signal Processing

Tue, 19 Apr 2016 00:00:00 +0000

Recently, I’ve sucessfully tested the new driver ciruit for my ultrasonic anemometer. It performed even better than I expected and I will be happy to use it pretty much as it is.

Ultrasonic Anemometer Part 15: A new attempt

Tue, 22 Mar 2016 00:00:00 +0000

It’s been about one and a half years since I started out with my ultrasonic anemometer project. Like others before me I had to notice that this a much more demanding project than it appears to be at first. After countless hours of development and testing I have built this Arduino shield. It worked but the reliability of the measurements was never what I had aimed for. The problem was mainly how to figure out the absolute phase of the received signal. So the measurements were always precise - but sometimes off by a full wavelength. Then I was more or less inactive for most of 2015, mainly due to personal reasons. So the project was kind of stuck but i kept (and keep) getting a lot of encouraging feedback from you folks. I came up with new circuit ideas and decided to pretty much start with an entirely new design and to re-think each and every design choice I had made back then.

Arduino MPPT Solar Charger Shield – Software

Fri, 12 Feb 2016 00:00:00 +0000

There have been two previous posts on this project: one on the concept and the hardware and one on hardware testing. You probably want to check them out first if you’re not yet familiar with this project. Or even better: Click here for an overview over this project.

Arduino Ultrasonic Anemometer Part 11: Testing the new hardware

Sun, 30 Nov 2014 00:00:00 +0000

Today I’ll go through each part of my new Arduino shield to see if it performs as expected.

If you’re new to my Arduino-based ultrasonic wind meter project, you might want to click here for an overview: /projects/arduino-ultrasonic-anemometer/

Arduino Ultrasonic Anemometer Part 9: A new hardware

Mon, 24 Nov 2014 00:00:00 +0000

My first wind meter prototype is kind of working. The software will need improvement to make this wind meter into something really useful. But both hardware and software are basically functional and can be built up upon.

Arduino Ultrasonic Anemometer Part 7: Basic software

Thu, 20 Nov 2014 00:00:00 +0000

Today I’ll tell you how I got started with my software. If you’re new to my blog you might want to click here for an overview over my arduino-based wind meter project: /projects/arduino-ultrasonic-anemometer/

Arduino Ultrasonic Anemometer Part 4: Testing the analog board

Sun, 16 Nov 2014 00:00:00 +0000

In this post I will go through the testing of the analog circuit and what I had to do to make it work properly. Click here for an overview over this series of posts on the anemometer project: /projects/arduino-ultrasonic-anemometer/

Arduino Ultrasonic Anemometer Part 3: Analog Circuit

Sat, 15 Nov 2014 00:00:00 +0000

Today I’ll go through the details of the analog cirquit. Click here for an overview over this series of posts on the anemometer project: /projects/arduino-ultrasonic-anemometer/

The analog board ready to be connected

This is what I would consider the heart of this wind meter. This is where the received signal is amplified and processed so the overall accuracy and reliability of the entire project really depends on it. The functionality of this board can be summarized as follows: